Yearly Archive September 14, 2020

In fact, no matter what the equipment is, the installation environment is very important. It’s not to say that the environment is particularly good, but it can’t be too bad. For example, the floor can’t be uneven. So let’s learn about the requirements of CNC machining center on the installation environment?

1. Location requirements

It should be far away from the vibration source and direct sunlight. If there is a seismic source nearby, an earthquake proof trench should be set up.

1. Temperature and humidity

The optimal processing temperature of CNC machining center is below 30 ℃. If the ambient temperature and humidity are too high, the service life of the control system components may be reduced. If the ambient humidity is too high, it may lead to the short circuit and fault of the integrated circuit board.

1. Voltage and current control

There are many processing equipment in the workshop, which will cause excessive fluctuation of the power grid. We need to control the voltage and current within the allowable range of the machining center and keep it stable, otherwise the work of the system may be affected. The power supply shall be 380V ± 10%, three-phase AC.

As we all know, after the installation of CNC machining center, the acceptance still needs to be done, because the acceptance of CNC machining center directly affects the equipment put into use of the manufacturer. The general factory acceptance standard is to directly carry out the workpiece processing test. In fact, after the workpiece processing test, it can be basically determined that the key parts of the machining center meet the standards, and in the case of normal use There is no problem. About CNC machining center spindle performance inspection is what?

1. Select low, medium and high speed. The main shaft starts 5 times in a row, then stops the operation to check the flexibility and reliability of its action. At the same time, check whether the power display on the load meter meets the requirements.
2. It can input data manually, so that the spindle gradually increases from low speed to the maximum allowable speed. Check whether the speed is normal, the general allowable error should not exceed ± 10%. While checking the spindle speed. Observe whether the noise, vibration and temperature rise of the spindle are normal. The temperature rise of the spindle is 15 “C after running at high speed for 2 h.
3. In order to check the flexibility and reliability of the spindle action, the spindle can be stopped accurately and operated continuously for more than 5 times.

CNC machining refers to NC machining, which is a method of controlling mechanical movement and machining process by using digital information.

The traditional mechanical processing is operated by hand with ordinary machine tools. When machining, the metal is cut by hand shaking the mechanical cutter, and the accuracy of products is measured with caliper and other tools by eyes. However, the traditional manual processing is far from meeting the production requirements.

Therefore, the emergence of CNC machining provides the possibility for the standardization, accuracy and efficiency of machining, and CNC machining is also brilliant in the radiator industry.

In order to obtain high-quality products, ordinary processing technology must have complex processes, such as the selection of cutting route, shape and size of radiator panel, and the force used for processing on different materials is not the same, so in order to reduce the error in the specific operation, the efficiency must not be high.

However, with CNC processing, all processes are first arranged and designed, incorporated into the processing program, simplify the process and carry out each step orderly, without affecting the efficiency of human factors, greatly improving the production efficiency of manufacturers.

Nowadays, many businesses not only have high requirements for the heat dissipation performance of the radiator, but also have the pursuit on the beauty of the appearance, and the application of CNC processing can achieve compatibility between the two.

CNC machining quality is stable, the finished product surface texture is clear, metal texture is strong, smooth, no scratch, no missing angle, and the heat dissipation coefficient strength of raw materials will not be changed under precision processing.

Manufacturers can adjust the specific process in the process to enhance its heat dissipation performance, such as Zhigao’s oxidation, wire drawing, paint baking, sand blasting and other processes can be carried out under the CNC operation.

It is believed that friends who have been in contact with radiators are not unfamiliar with fin shaped radiators and sunflower radiators. In fact, CNC processing is indispensable to the production of radiators with special requirements on the appearance.

Traditional processing technology for special, complex parts can not achieve high-efficiency and fine production, and with the help of numerical control processing, you only need to set the programming to process the desired surface, and the finished product is firm and durable, accurate and tight.

The machining method of CNC workpiece surface depends on the technical requirements of machined surface. However, it should be noted that these technical requirements are not necessarily the requirements specified in the part drawing, and sometimes they may be higher than the requirements on the part drawing due to process reasons. For example, because the datum does not coincide, the machining requirements of some CNC machining parts are raised. Or it may put forward higher processing requirements because it is used as a precision reference.

When the technical requirements of the surface of CNC machining parts are defined, the final processing method can be selected according to the requirements, and the processing methods of several steps and each step are determined. The selected CNC machining method should meet the requirements of parts quality, good processing economy and high production efficiency. Therefore, the following factors should be considered when selecting the processing method:

1. There is a large range of machining accuracy and surface roughness that any CNC machining method can obtain, but only in a narrow range is economical, and the machining accuracy in this range is economic. Therefore, when selecting the processing method, we should choose the corresponding processing method which can obtain the economic machining accuracy.
2. The properties of CNC machining parts should be considered.
3. The structural shape and size of CNC machining parts should be considered.
4. Productivity and economic requirements should be considered. In mass production, advanced technology with high efficiency should be adopted. Even can fundamentally change the manufacturing method of the blank, can reduce the amount of mechanical processing labor.
5. The existing equipment and technical conditions of the factory or workshop should be considered. When selecting the processing method, the existing equipment should be fully utilized, the potential of the enterprise should be tapped, and the enthusiasm and creativity of the workers should be brought into play. However, it is also necessary to continuously improve the existing processing methods and equipment, adopt new technologies and improve the technological level

This processing technology has been widely used in our industry. It is very common in our industry. The requirements of this processing technology are very high. Compared with the traditional process, it can achieve better results. There are many advantages that other processing methods do not have. What are the advantages of CNC precision parts processing?

1. Multi axis control linkage: in general, three axis linkage is the most frequently used, but through some adjustment, four axis, five axis, seven axis and even more linkage axis machining center can be achieved.
2. Parallel machine tool: the common machining center has a fixed function. The machining center and turning center, or vertical and horizontal machining center can be combined together, which can increase the processing range and processing capacity of the machining center
3. Tool breakage warning: using some technical detection means, we can find the tool wear and damage in time, and give an alarm, so that the tool can be replaced in time to ensure the processing quality of parts.
4. The management of the same cutting tool can improve the working efficiency of multiple cutting tools at the same time.
5. Overload and power-off protection of machine tool: according to the maximum load level set according to the load in the production process, when the load reaches the set value, the machine tool can realize automatic power-off to protect the machine tool.

Many people will get some different prices when they go to the market for processing. Sometimes it is because of different prices, sometimes it is the same product, but in different businesses, they will get different prices. There are many influencing factors. So let’s learn how to calculate the price of hardware parts processing?

1. First look at your drawings and technical requirements
2. There are differences in materials and labor in different places, and there is a big price difference in some places
3. General parts are calculated according to material cost + processing cost + profit. The processing cost depends on the process. The price of different processing equipment is of course different. Some are calculated according to working hours (turning time, grinding time, etc.), and some are calculated according to working procedures (such as how much is a folding plate for a knife, how much is a common drill hole, etc.)
4. There is also a problem of quantity. A large quantity is certainly cheap. If it is a single piece, even if it is a small piece and the materials are not retailed, you should calculate the price of the whole board! For example, if you say 0.3, the manufacturer does not use it frequently. If you only buy one or two pieces of materials, if you only buy one board at a time (such as 1220 * 2440), you will be wrongly spent on the material cost.
5. If the parts processing factory can solve the problems of the processing factory itself, of course, there is no problem. If the processing factory itself has some processes to be outsourced, the price will be correspondingly increased. If you are outsourcing, it means that you have been outsourced twice! So you should find the right one to find what they can do and what they are good at.

In the process of processing, because we want to ensure the effect of the product, as well as our personal safety, so we need to pay attention to a lot of matters in the operation, such as some correct operation methods, these are basic, the correct operation method can avoid damaging the parts of the equipment, then we will learn what we should pay attention to in CNC processing What about the item?

(1) When the workpiece is too high, it should be roughened by different length of knife in layers. After using a big knife for roughening, the residual material should be removed with a small knife.

(2) The flat bottomed cutter is used to process the plane, and the ball cutter is used less so as to reduce the processing time; if there is a slope and it is an integer, it should be processed with a slope cutter.

(3) The reasonable setting of tolerance can balance the machining accuracy and the computer calculation time, do more procedures, and reduce the idle tool time.

(4) If the hardness of the blank material is high, the reverse milling is selected; if the hardness of the blank material is low, the down milling is selected. Rough machining up milling, finish machining down milling.

(5) The tool material has good toughness and low hardness, which is suitable for rough machining, while the tool material with poor toughness and high hardness is suitable for finish machining.

Many people may not have too much understanding of these two, but in our industrial industry, the scope of application is still very wide. 3D printing and CNC machining are the more common production processes in the field of precision mechanical processing. They have similarities and differences. So let’s take a look at the advantages of CNC processing compared with 3D printing?

1、 Advantages of surface treatment

CNC machines provide better surface finish than 3D printing because the material does not deform during processing. Rigid materials and cutting actions keep the product together and there is less chance of error or deformation. The surface finish of 3D printing is poor. The material is bent, twisted or twisted because the material is laminated heated plastic.

2、 Prototype integrity improved

The numerical control machine tool does not heat the material and carries on the transformation. Materials remain stronger and have better structural integrity than 3D printers, and 3D printers must heat materials to build the desired product. 3D printers may also need to add foreign materials to the mixture to make prototypes, while CNC machines do not.

3、 Prototyping becomes easier

CNC machines are more suitable for prototypes that can withstand structural testing because they carve designs out of materials. They can also build prototypes using the exact materials that will be used to make the final product. Structural tests and changes will be more accurate because they use the same materials. This can speed up the production process, because the change will be design rather than material. 3D printers do not make prototypes with structural strength, so they cannot be physically tested.

4、 Price and volume do not represent price

The cost of 3D printing depends on the volume of material required. The final product quantity does not determine the price of CNC machine tools. For large orders, 3D printing is not cost-effective, which is the booming situation of CNC machine tools.

5、 The level of tolerance is rising

CNC machines are more accurate, so parts have better tolerances than 3D printers. Due to the tolerance level, prototypes with shafts or connections to other parts will have higher quality and are more likely to fit other parts.

6、 Quality benefits CNC

The larger layers of 3D printers are faster, but not as high-quality as smaller layers. If you need a prototype, you can choose to get it quickly but with a slightly lower quality, or wait longer to get the best quality prototype that the printer can provide. CNC machine tools allow you to choose the resolution of the items. They can provide different qualities in a short period of time, making them ideal for rapid build and instant test results.

7、 Cost reduction

If you can choose which manufacturing method to use for your product, CNC processing is usually cheaper than 3D printing.

We all know that no matter what work we are doing, we should do some preparatory work first, so as to ensure that our work can be carried out smoothly. Therefore, whether it is the preparatory work or to understand some common sense, these are very important. So let’s learn what we need to know before CNC processing?

CNC processing in Dongguan

1. Datum first: that is to process the datum plane first. During the machining process of parts, the surface as the positioning datum should be processed first, so as to provide the precise datum for the subsequent processing as soon as possible.
2. Distinguish the processing stage: precision CNC machining quality request high appearance, all distinguish the processing stage, generally can be divided into rough machining, semi finishing and finishing three stages. The first is to ensure the quality of processing; it is conducive to the scientific use of equipment; it is convenient to organize the heat treatment process; and it is convenient to find the defects of the blank.
3. Face before hole: for parts such as box, bracket and connecting rod, the plane should be machined first and then the hole should be processed. In this way, the hole can be processed by plane positioning, which ensures the accuracy of plane and hole orientation, and brings convenience to the processing of holes on the plane.
4. Finishing: the primary surface finishing, such as grinding, honing, finishing, rolling, etc., should be placed at the end of the process path. There are two parts in drawing up the general rules of fine CNC machining road and the drawing up of precision CNC machining procedure. The first is to draw up the process path of parts processing, and then determine the process scale of each process, the equipment and process equipment used, as well as the cutting standard, man hour quota, etc

No matter what kind of work, there must be some matters to pay attention to in this process, so as to better ensure our work efficiency and product quality. Now aluminum alloy is widely used with high-precision instruments, so the requirements are higher and higher. At this time, whether it is manufacturing or processing, what matters should be paid attention to in CNC processing of aluminum alloy?

1. The speed of white steel knife should not be too fast.
2. When the workpiece is too high, please thicken it with a knife of different grade length.
3. After roughening with a rough knife, remove the excess with the knife, and grind the knife after ensuring the excess.
4. The plane is processed with flat bottom edge instead of ball edge to reduce processing time.
5. The four corners of the calibration plane must be flat.
6. The inclination is an integer, which is processed with an inclined cutter, such as tube position.
7. Before each work, want to clear the remaining amount of the previous work after processing, to avoid empty tool and redundant processing.
8. Try to take a simple path. For example, shape, trenching, avoiding single side, lapping, etc.
9. When taking wcut, if you can go to finish, please don’t take rough.
10. In the case of shape light knife, the light should be coarsened first and then exposed. When the workpiece is too high, it should be illuminated first and then.
11. The tolerance should be set reasonably to balance the machining accuracy and computer calculation time. The tolerance is set to 1 / 5 of the remaining value when it is turned on, and 0.01 for a light knife.
12. Add more projects to reduce the time of empty knife. Think more and reduce the chances of mistakes. Increase the auxiliary surface of the auxiliary line slightly to improve the processing condition.